Skip to content
Close
Cart
0 items

Jewelry Kit Instructions

Crystal Shamballa Bracelet Kit Instructions

by John Woodson 08 Jun 2022 0 Comments
(Step 1) Using your nipper tool take your 8' of knotting cord and cut it in half, leaving 2 equal pieces (4' each).(like this)(Step 2) Take one of your 4' segments and cut it in half leaving two 2' pieces and one 4' piece. (like this)(Step 3) Clip one of your 2' pieces of cord into your clipboard, leaving an 8" tail on both sides of the clip board.(Step 4) Load your beads, pull your cord tightly, and use your binder clip to clip your cord to the bottom of your board. This will be your guide line.(Step 5) Place your 4� cord under the guide line Keeping it even on both ends.(Step 6) Take the right side of your cord over the guide and under your left side of cord. Now take the left side under your guide and up through the loop.(Step 7) Take the left side of your cord over your guide, and under the right side, then take the right side of your cord moving it under the guide and over the left cord (through the loop)(Step 8) Repeat Steps 6 and 7 3 times then push up your bead.(Step 9) After you've pushed up your first bead follow this pattern belowStep 7Step 6Step 7Step 6Push up your BeadStep 7Step 6Step 7Step 6Push up your BeadStep 7Step 6Step 7Step 6Push up your BeadStep 7Step 6Step 7Step 6Push up your BeadStep 7Step 6Step 7Step 6Push up your beadStep 7Step 6Step 7Step 6Push up your final beadsStep 7Step 6Step 7Step 6Step 7Step 6Step 7Step 6After completing steps 1-9 the end of your bracelet should look like this(Step 10) You should have some excess cord on the right and left side of your guide line. Lets clean those up.Glue around both area�s you have extra cord and let is dry for a few minutes.(Step 11) Now that the glue has had a chance to dry, go ahead and snip off the remaining cordWhat you have now, should look very similar to this.(Step 12) At this point we get back to our knotting to close off our bracelet. Make sure to overlap your remaining cord (image above) as this will now be our guide line.(Step 13) Use your remaining 2� cord and place it evenly under your new guidelines.(Step 14) From here we will be going back to page one using steps 6 and 7 repeatedly until you wrap an amount you are happy with for sizing. (Usually 14 Knots or the pattern below)Step 6Step 7Step 6 Step 7Step 6Step 7Step 6Step 7Step 6Step 7Step 6Step 7Step 6Step 7(Step 15) Once you�ve finished knotting, slide your stopper beads onto your guide line to give you a way to tighten your bracelet.(Step 16) Glue and cut the remaining segments of your 2� cord(Step 17) Lastly, you want to make a tight knot at the end of your stopper beads, gluing to secures, and cutting off any excess cord. Now just let it dry for 24 hrs. Then show it off.
930 x 520px

SPRING SUMMER LOOKBOOK

Sample Block Quote

Praesent vestibulum congue tellus at fringilla. Curabitur vitae semper sem, eu convallis est. Cras felis nunc commodo eu convallis vitae interdum non nisl. Maecenas ac est sit amet augue pharetra convallis.

Sample Paragraph Text

Praesent vestibulum congue tellus at fringilla. Curabitur vitae semper sem, eu convallis est. Cras felis nunc commodo eu convallis vitae interdum non nisl. Maecenas ac est sit amet augue pharetra convallis nec danos dui. Cras suscipit quam et turpis eleifend vitae malesuada magna congue. Damus id ullamcorper neque. Sed vitae mi a mi pretium aliquet ac sed elitos. Pellentesque nulla eros accumsan quis justo at tincidunt lobortis deli denimes, suspendisse vestibulum lectus in lectus volutpate.
Prev Post
Next Post

Leave a comment

All blog comments are checked prior to publishing

Thanks for subscribing!

This email has been registered!

Shop the look

Choose Options

Recently Viewed





Close
Back In Stock Notification
this is just a warning
Login Close
Close
Shopping Cart
0 items